Claude review: Add support for Tianma TA066VVHM03 DSI panel

Claude review: Add support for Tianma TA066VVHM03 DSI panel

[Claude Code Review Bot]

Overall Series Review

Subject: Add support for Tianma TA066VVHM03 DSI panel
Author: Alexander Koskovich <AKoskovich@pm.me>
Patches: 6
Reviewed: 2026-03-09T07:59:02.650574

---

This is a straightforward 2-patch series adding a new DSI panel driver for the Tianma TA066VVHM03 AMOLED panel (6.59" 1080x2340 with DSC), found in the ASUS ROG Phone 3. The driver was generated with `linux-mdss-dsi-panel-driver-generator`. The series uses modern APIs (`devm_drm_panel_alloc`, `drm_connector_helper_get_modes_fixed`, `mipi_dsi_multi_context`), which is good.

However, there are a few issues:
1. **Hard dependency on unmerged `dsc_slice_per_pkt` support** — this series cannot build without that patch being merged first.
2. **Missing error-path cleanup in `prepare`** — after PPS or compression mode fails, GPIOs and regulators are left enabled.
3. **Binding/driver mismatch for `enable-gpios`** — the binding makes it optional but the driver requires it.

---

---
Generated by Claude Code Patch Reviewer

Claude review: Add support for Tianma TA066VVHM03 DSI panel

[Claude Code Review Bot]

Overall Series Review

Subject: Add support for Tianma TA066VVHM03 DSI panel
Author: Alexander Koskovich <AKoskovich@pm.me>
Patches: 7
Reviewed: 2026-03-10T12:50:30.758142

---

This is a 2-patch series adding a new DSI panel driver for the Tianma TA066VVHM03 6.59" AMOLED panel with DSC compression, used in the ASUS ROG Phone 3. The series is clean and follows modern panel driver patterns (uses `devm_drm_panel_alloc`, `mipi_dsi_multi_context`, `drm_connector_helper_get_modes_fixed`, etc.). The DT binding already has a Reviewed-by from Krzysztof Kozlowski.

There are a few issues worth addressing:

1. **Dependency on unmerged `dsc_slice_per_pkt` support** — the cover letter acknowledges this, but it means the driver won't compile on mainline.
2. **Missing cleanup in `prepare()` error paths** — PPS/compression failures leak regulators and GPIOs.
3. **`enable-gpios` mismatch between binding and driver** — optional in binding, mandatory in driver probe.
4. **Questionable LPM handling in `_off()`** — clears LPM before sending DCS commands, which is unusual.
5. **Refresh rate of 160 Hz** looks atypical for a phone panel — may be intentional, but worth confirming.

Overall the series is in reasonable shape. The DT binding patch is fine; the panel driver needs minor fixes to error handling and consistency.

---
Generated by Claude Code Patch Reviewer

[PATCH v3 0/2] Add support for Tianma TA066VVHM03 DSI panel

[Alexander Koskovich]

Add dt-binding and driver for the Tianma TA066VVHM03 6.59" 1080x2340
AMOLED DSI panel with DSC compression, found in the ASUS ROG Phone 3.

This panel depends on slice_per_pkt support currently being reviewed:
https://lore.kernel.org/linux-arm-msm/20251001135914.13754-3-caojunjie650@gmail.com

Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
---
Changes in v3:
- Fixed From/SoB mismatch
- Link to v2: https://lore.kernel.org/r/20260308-tianma-ta066vvhm03-v2-0-5f2344685133@pm.me

Changes in v2:
- Move additionalProperties after required block in bindings
- Link to v1: https://lore.kernel.org/r/20260308-tianma-ta066vvhm03-v1-0-869fac443b20@pm.me

---
Alexander Koskovich (2):
      dt-bindings: display: panel: Document Tianma TA066VVHM03
      drm/panel: Add support for Tianma TA066VVHM03 panel

 .../bindings/display/panel/tianma,ta066vvhm03.yaml |  67 ++++
 MAINTAINERS                                        |   6 +
 drivers/gpu/drm/panel/Kconfig                      |  11 +
 drivers/gpu/drm/panel/Makefile                     |   1 +
 drivers/gpu/drm/panel/panel-tianma-ta066vvhm03.c   | 387 +++++++++++++++++++++
 5 files changed, 472 insertions(+)
---
base-commit: 1f318b96cc84d7c2ab792fcc0bfd42a7ca890681
change-id: 20260308-tianma-ta066vvhm03-a72bd18f2b3f

Best regards,
-- 
Alexander Koskovich <akoskovich@pm.me>

[PATCH v3 1/2] dt-bindings: display: panel: Document Tianma TA066VVHM03

[Alexander Koskovich]

Add bindings for the Tianma TA066VVHM03 6.59" 1080x2340 AMOLED DSI
panel with DSC compression, found in the ASUS ROG Phone 3.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
---
 .../bindings/display/panel/tianma,ta066vvhm03.yaml | 67 ++++++++++++++++++++++
 1 file changed, 67 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/tianma,ta066vvhm03.yaml b/Documentation/devicetree/bindings/display/panel/tianma,ta066vvhm03.yaml
new file mode 100644
index 000000000000..9bd80cd9662f
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/tianma,ta066vvhm03.yaml
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/tianma,ta066vvhm03.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Tianma TA066VVHM03 AMOLED DSI Panel
+
+maintainers:
+  - Alexander Koskovich <akoskovich@pm.me>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: tianma,ta066vvhm03
+
+  reg:
+    maxItems: 1
+    description: DSI virtual channel
+
+  vddio-supply: true
+  vci-supply: true
+  vdd-supply: true
+  port: true
+  enable-gpios: true
+  reset-gpios: true
+
+required:
+  - compatible
+  - reg
+  - vddio-supply
+  - vci-supply
+  - vdd-supply
+  - reset-gpios
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    dsi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        panel@0 {
+            compatible = "tianma,ta066vvhm03";
+            reg = <0>;
+
+            enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>;
+
+            vci-supply = <&vreg_l10a>;
+            vdd-supply = <&vreg_l3c>;
+            vddio-supply = <&vreg_l14a>;
+
+            port {
+                panel_in: endpoint {
+                    remote-endpoint = <&mdss_dsi0_out>;
+                };
+            };
+        };
+    };
+...

-- 
2.53.0

[PATCH v3 2/2] drm/panel: Add support for Tianma TA066VVHM03 panel

[Alexander Koskovich]

Add driver for the Tianma TA066VVHM03 6.59" 1080x2340 AMOLED DSI
panel with DSC compression, found in the ASUS ROG Phone 3.

Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
---
 MAINTAINERS                                      |   6 +
 drivers/gpu/drm/panel/Kconfig                    |  11 +
 drivers/gpu/drm/panel/Makefile                   |   1 +
 drivers/gpu/drm/panel/panel-tianma-ta066vvhm03.c | 387 +++++++++++++++++++++++
 4 files changed, 405 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 77fdfcb55f06..06149cd65f52 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8382,6 +8382,12 @@ F:	Documentation/devicetree/bindings/display/rockchip/rockchip,dw-dp.yaml
 F:	drivers/gpu/drm/bridge/synopsys/dw-dp.c
 F:	include/drm/bridge/dw_dp.h
 
+DRM DRIVER FOR TIANMA TA066VVHM03 PANELS
+M:	Alexander Koskovich <akoskovich@pm.me>
+S:	Maintained
+F:	Documentation/devicetree/bindings/display/panel/tianma,ta066vvhm03.yaml
+F:	drivers/gpu/drm/panel/panel-tianma-ta066vvhm03.c
+
 DRM DRIVER FOR TI DLPC3433 MIPI DSI TO DMD BRIDGE
 M:	Jagan Teki <jagan@amarulasolutions.com>
 S:	Maintained
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 307152ad7759..c818c701bdf6 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -1122,6 +1122,17 @@ config DRM_PANEL_TDO_TL070WSH30
 	  24 bit RGB per pixel. It provides a MIPI DSI interface to
 	  the host, a built-in LED backlight and touch controller.
 
+config DRM_PANEL_TIANMA_TA066VVHM03
+	tristate "Tianma TA066VVHM03 panel driver"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	depends on BACKLIGHT_CLASS_DEVICE
+	help
+	  Say Y if you want to enable support for the Tianma TA066VVHM03 panel
+	  driver. The panel has a 1080x2340 resolution and uses 24 bit RGB per
+	  pixel. It provides a MIPI DSI interface to the host and has a
+	  built-in touch controller.
+
 config DRM_PANEL_TPO_TD028TTEC1
 	tristate "Toppoly (TPO) TD028TTEC1 panel driver"
 	depends on OF && SPI
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index aeffaa95666d..db257778b9f1 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -110,6 +110,7 @@ obj-$(CONFIG_DRM_PANEL_SONY_TD4353_JDI) += panel-sony-td4353-jdi.o
 obj-$(CONFIG_DRM_PANEL_SONY_TULIP_TRULY_NT35521) += panel-sony-tulip-truly-nt35521.o
 obj-$(CONFIG_DRM_PANEL_STARTEK_KD070FHFID015) += panel-startek-kd070fhfid015.o
 obj-$(CONFIG_DRM_PANEL_TDO_TL070WSH30) += panel-tdo-tl070wsh30.o
+obj-$(CONFIG_DRM_PANEL_TIANMA_TA066VVHM03) += panel-tianma-ta066vvhm03.o
 obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o
 obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o
 obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o
diff --git a/drivers/gpu/drm/panel/panel-tianma-ta066vvhm03.c b/drivers/gpu/drm/panel/panel-tianma-ta066vvhm03.c
new file mode 100644
index 000000000000..9bf0f4ab6792
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-tianma-ta066vvhm03.c
@@ -0,0 +1,387 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Generated with linux-mdss-dsi-panel-driver-generator from vendor device tree.
+ * Copyright (c) 2026 Alexander Koskovich <akoskovich@pm.me>
+ */
+
+#include <linux/backlight.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/regulator/consumer.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/display/drm_dsc.h>
+#include <drm/display/drm_dsc_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_probe_helper.h>
+
+struct tianma_ta066vvhm03 {
+	struct regulator_bulk_data *supplies;
+	struct gpio_desc *enable_gpio;
+	struct gpio_desc *reset_gpio;
+	struct mipi_dsi_device *dsi;
+	struct drm_dsc_config dsc;
+	struct drm_panel panel;
+};
+
+static const struct regulator_bulk_data tianma_ta066vvhm03_supplies[] = {
+	{ .supply = "vddio" },
+	{ .supply = "vci" },
+	{ .supply = "vdd" },
+};
+
+static inline
+struct tianma_ta066vvhm03 *to_tianma_ta066vvhm03(struct drm_panel *panel)
+{
+	return container_of(panel, struct tianma_ta066vvhm03, panel);
+}
+
+static void tianma_ta066vvhm03_reset(struct tianma_ta066vvhm03 *ctx)
+{
+	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+	usleep_range(1000, 2000);
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+	usleep_range(5000, 6000);
+	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+	usleep_range(10000, 11000);
+}
+
+static int tianma_ta066vvhm03_on(struct tianma_ta066vvhm03 *ctx)
+{
+	struct mipi_dsi_multi_context dsi_ctx = { .dsi = ctx->dsi };
+
+	ctx->dsi->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xb0, 0x04);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xb3, 0x00);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xf1, 0x2a);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc1, 0x0c);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc1,
+				     0x94, 0x42, 0x00, 0x16, 0x05, 0x00, 0x00,
+				     0x00, 0x10, 0x00, 0x10, 0x00, 0xaa, 0x8a,
+				     0x02, 0x10, 0x00, 0x10, 0x00, 0x00, 0x3f,
+				     0x3f, 0x03, 0xff, 0x03, 0xff, 0x23, 0xff,
+				     0x03, 0xff, 0x23, 0xff, 0x03, 0xff, 0x00,
+				     0x40, 0x40, 0x00, 0x00, 0x10, 0x01, 0x00,
+				     0x0c);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc2,
+				     0x09, 0x24, 0x0e, 0x00, 0x00, 0x0e);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc4,
+				     0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+				     0x00, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00,
+				     0x00, 0x2f, 0x00, 0x01);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xcf,
+				     0x64, 0x0b, 0x00, 0xc0, 0x02, 0xa6, 0x04,
+				     0x7f, 0x0b, 0x77, 0x0b, 0x8b, 0x04, 0x04,
+				     0x04, 0x04, 0x04, 0x04, 0x04, 0x04, 0x04,
+				     0x05, 0x05, 0x05, 0x00, 0x10, 0x01, 0x68,
+				     0x01, 0x68, 0x01, 0x68, 0x01, 0x68, 0x01,
+				     0x68, 0x01, 0x69, 0x03, 0x98, 0x03, 0x70,
+				     0x03, 0x70, 0x03, 0x70, 0x03, 0x70, 0x00,
+				     0x10, 0x01, 0x68, 0x01, 0x68, 0x01, 0x68,
+				     0x01, 0x68, 0x01, 0x68, 0x01, 0x68, 0x03,
+				     0x98, 0x03, 0x70, 0x03, 0x70, 0x03, 0x70,
+				     0x03, 0x70, 0x01, 0x42, 0x01, 0x42, 0x01,
+				     0x42, 0x01, 0x42, 0x01, 0x42, 0x01, 0x42,
+				     0x01, 0x42, 0x01, 0x42, 0x01, 0x42, 0x01,
+				     0x42, 0x01, 0x42, 0x01, 0x42, 0x1c, 0x1c,
+				     0x1c, 0x1c, 0x1c, 0x1c, 0x1c, 0x1c, 0x1c,
+				     0x1c, 0x1c, 0x00, 0x01, 0x9a, 0x01, 0x9a,
+				     0x01, 0x9a, 0x05, 0xae, 0x05, 0xae, 0x09,
+				     0xa4, 0x09, 0xa4, 0x09, 0xa4, 0x09, 0xa4,
+				     0x09, 0xa4, 0x09, 0xa4, 0x0f, 0xc3, 0x19);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd7,
+				     0x00, 0xa9, 0x34, 0x00, 0x20, 0x02, 0x00,
+				     0x00, 0x30, 0x00, 0x40, 0x00, 0x00, 0x00,
+				     0x00, 0x00, 0x00, 0x10, 0x02, 0x00, 0x40,
+				     0x09, 0x00, 0x00, 0x30);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd8,
+				     0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+				     0x00, 0x00, 0x30, 0x00, 0x30, 0x00, 0x30,
+				     0x00, 0x30, 0x00, 0x30, 0x05, 0x00, 0x00,
+				     0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+				     0x00, 0x00, 0x30, 0x00, 0x00, 0x00, 0x00,
+				     0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+				     0x00, 0x00, 0x0f, 0x00, 0x2f, 0x00, 0x00,
+				     0x00, 0x0e, 0x00, 0x00, 0x00, 0x00, 0x00,
+				     0x00, 0x00, 0x00);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xbb,
+				     0x59, 0xc8, 0xc8, 0xc8, 0xc8, 0xc8, 0xc8,
+				     0xc8, 0xc8, 0xc8, 0x4a, 0x48, 0x46, 0x44,
+				     0x42, 0x40, 0x3e, 0x3c, 0x3a, 0x00, 0xff,
+				     0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+				     0xff, 0x04, 0x00, 0x04, 0x04, 0x42, 0x04,
+				     0x69, 0x5a, 0x00, 0x0a, 0xb0, 0x0f, 0xff,
+				     0x0f, 0xff, 0x0f, 0xff, 0x14, 0x81, 0xf4);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xe8, 0x00, 0x02);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xe4, 0x00, 0x0a);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xb0, 0x80);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd4, 0x93);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xde, 0x30);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xb0, 0x04);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xdf, 0x50, 0x40);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xf3,
+				     0x50, 0x00, 0x00, 0x00, 0x00);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xf2, 0x11);
+	mipi_dsi_usleep_range(&dsi_ctx, 1000, 2000);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xf3,
+				     0x01, 0x00, 0x00, 0x00, 0x01);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xf4, 0x00, 0x02);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xf2, 0x19);
+	mipi_dsi_usleep_range(&dsi_ctx, 1000, 2000);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xdf, 0x50, 0x42);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, MIPI_DCS_WRITE_CONTROL_DISPLAY,
+				     0x24);
+	mipi_dsi_dcs_set_tear_on_multi(&dsi_ctx, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
+	mipi_dsi_dcs_set_column_address_multi(&dsi_ctx, 0x0000, 0x0437);
+	mipi_dsi_dcs_set_page_address_multi(&dsi_ctx, 0x0000, 0x0923);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xb0, 0x80);
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xe6, 0x01);
+	mipi_dsi_dcs_exit_sleep_mode_multi(&dsi_ctx);
+	mipi_dsi_msleep(&dsi_ctx, 100);
+	mipi_dsi_dcs_set_display_on_multi(&dsi_ctx);
+
+	return dsi_ctx.accum_err;
+}
+
+static int tianma_ta066vvhm03_off(struct tianma_ta066vvhm03 *ctx)
+{
+	struct mipi_dsi_multi_context dsi_ctx = { .dsi = ctx->dsi };
+
+	ctx->dsi->mode_flags &= ~MIPI_DSI_MODE_LPM;
+
+	mipi_dsi_dcs_set_display_off_multi(&dsi_ctx);
+	mipi_dsi_dcs_enter_sleep_mode_multi(&dsi_ctx);
+	mipi_dsi_msleep(&dsi_ctx, 120);
+
+	return dsi_ctx.accum_err;
+}
+
+static int tianma_ta066vvhm03_prepare(struct drm_panel *panel)
+{
+	struct tianma_ta066vvhm03 *ctx = to_tianma_ta066vvhm03(panel);
+	struct drm_dsc_picture_parameter_set pps;
+	struct device *dev = &ctx->dsi->dev;
+	int ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(tianma_ta066vvhm03_supplies), ctx->supplies);
+	if (ret < 0) {
+		dev_err(dev, "Failed to enable regulators: %d\n", ret);
+		return ret;
+	}
+
+	gpiod_set_value_cansleep(ctx->enable_gpio, 1);
+
+	tianma_ta066vvhm03_reset(ctx);
+
+	ret = tianma_ta066vvhm03_on(ctx);
+	if (ret < 0) {
+		dev_err(dev, "Failed to initialize panel: %d\n", ret);
+		gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+		gpiod_set_value_cansleep(ctx->enable_gpio, 0);
+		regulator_bulk_disable(ARRAY_SIZE(tianma_ta066vvhm03_supplies), ctx->supplies);
+		return ret;
+	}
+
+	drm_dsc_pps_payload_pack(&pps, &ctx->dsc);
+
+	ret = mipi_dsi_picture_parameter_set(ctx->dsi, &pps);
+	if (ret < 0) {
+		dev_err(panel->dev, "failed to transmit PPS: %d\n", ret);
+		return ret;
+	}
+
+	ret = mipi_dsi_compression_mode(ctx->dsi, true);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable compression mode: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int tianma_ta066vvhm03_unprepare(struct drm_panel *panel)
+{
+	struct tianma_ta066vvhm03 *ctx = to_tianma_ta066vvhm03(panel);
+	struct device *dev = &ctx->dsi->dev;
+	int ret;
+
+	ret = tianma_ta066vvhm03_off(ctx);
+	if (ret < 0)
+		dev_err(dev, "Failed to un-initialize panel: %d\n", ret);
+
+	gpiod_set_value_cansleep(ctx->enable_gpio, 0);
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+	regulator_bulk_disable(ARRAY_SIZE(tianma_ta066vvhm03_supplies), ctx->supplies);
+
+	return 0;
+}
+
+static const struct drm_display_mode tianma_ta066vvhm03_mode = {
+	.clock = (1080 + 24 + 4 + 10) * (2340 + 12 + 1 + 4) * 160 / 1000,
+	.hdisplay = 1080,
+	.hsync_start = 1080 + 24,
+	.hsync_end = 1080 + 24 + 4,
+	.htotal = 1080 + 24 + 4 + 10,
+	.vdisplay = 2340,
+	.vsync_start = 2340 + 12,
+	.vsync_end = 2340 + 12 + 1,
+	.vtotal = 2340 + 12 + 1 + 4,
+	.width_mm = 70,
+	.height_mm = 152,
+	.type = DRM_MODE_TYPE_DRIVER,
+};
+
+static int tianma_ta066vvhm03_get_modes(struct drm_panel *panel,
+					struct drm_connector *connector)
+{
+	return drm_connector_helper_get_modes_fixed(connector, &tianma_ta066vvhm03_mode);
+}
+
+static const struct drm_panel_funcs tianma_ta066vvhm03_panel_funcs = {
+	.prepare = tianma_ta066vvhm03_prepare,
+	.unprepare = tianma_ta066vvhm03_unprepare,
+	.get_modes = tianma_ta066vvhm03_get_modes,
+};
+
+static int tianma_ta066vvhm03_bl_update_status(struct backlight_device *bl)
+{
+	struct mipi_dsi_device *dsi = bl_get_data(bl);
+	u16 brightness = backlight_get_brightness(bl);
+	int ret;
+
+	dsi->mode_flags &= ~MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_set_display_brightness_large(dsi, brightness);
+	if (ret < 0)
+		return ret;
+
+	dsi->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	return 0;
+}
+
+static const struct backlight_ops tianma_ta066vvhm03_bl_ops = {
+	.update_status = tianma_ta066vvhm03_bl_update_status,
+};
+
+static struct backlight_device *
+tianma_ta066vvhm03_create_backlight(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	const struct backlight_properties props = {
+		.type = BACKLIGHT_RAW,
+		.brightness = 4095,
+		.max_brightness = 4095,
+	};
+
+	return devm_backlight_device_register(dev, dev_name(dev), dev, dsi,
+					      &tianma_ta066vvhm03_bl_ops, &props);
+}
+
+static int tianma_ta066vvhm03_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct tianma_ta066vvhm03 *ctx;
+	int ret;
+
+	ctx = devm_drm_panel_alloc(dev, struct tianma_ta066vvhm03, panel,
+				   &tianma_ta066vvhm03_panel_funcs,
+				   DRM_MODE_CONNECTOR_DSI);
+	if (IS_ERR(ctx))
+		return PTR_ERR(ctx);
+
+	ret = devm_regulator_bulk_get_const(dev,
+					    ARRAY_SIZE(tianma_ta066vvhm03_supplies),
+					    tianma_ta066vvhm03_supplies,
+					    &ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ctx->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->enable_gpio))
+		return dev_err_probe(dev, PTR_ERR(ctx->enable_gpio),
+				     "Failed to get enable-gpios\n");
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(ctx->reset_gpio))
+		return dev_err_probe(dev, PTR_ERR(ctx->reset_gpio),
+				     "Failed to get reset-gpios\n");
+
+	ctx->dsi = dsi;
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	dsi->lanes = 4;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags = MIPI_DSI_MODE_NO_EOT_PACKET |
+			  MIPI_DSI_CLOCK_NON_CONTINUOUS;
+
+	ctx->panel.prepare_prev_first = true;
+
+	ctx->panel.backlight = tianma_ta066vvhm03_create_backlight(dsi);
+	if (IS_ERR(ctx->panel.backlight))
+		return dev_err_probe(dev, PTR_ERR(ctx->panel.backlight),
+				     "Failed to create backlight\n");
+
+	drm_panel_add(&ctx->panel);
+
+	/* This panel only supports DSC; unconditionally enable it */
+	dsi->dsc = &ctx->dsc;
+	dsi->dsc_slice_per_pkt = 2;
+
+	ctx->dsc.dsc_version_major = 1;
+	ctx->dsc.dsc_version_minor = 1;
+
+	ctx->dsc.slice_height = 20;
+	ctx->dsc.slice_width = 540;
+	WARN_ON(1080 % ctx->dsc.slice_width);
+	ctx->dsc.slice_count = 1080 / ctx->dsc.slice_width;
+	ctx->dsc.bits_per_component = 10;
+	ctx->dsc.bits_per_pixel = 8 << 4; /* 4 fractional bits */
+	ctx->dsc.block_pred_enable = true;
+
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		drm_panel_remove(&ctx->panel);
+		return dev_err_probe(dev, ret, "Failed to attach to DSI host\n");
+	}
+
+	return 0;
+}
+
+static void tianma_ta066vvhm03_remove(struct mipi_dsi_device *dsi)
+{
+	struct tianma_ta066vvhm03 *ctx = mipi_dsi_get_drvdata(dsi);
+	int ret;
+
+	ret = mipi_dsi_detach(dsi);
+	if (ret < 0)
+		dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret);
+
+	drm_panel_remove(&ctx->panel);
+}
+
+static const struct of_device_id tianma_ta066vvhm03_of_match[] = {
+	{ .compatible = "tianma,ta066vvhm03" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, tianma_ta066vvhm03_of_match);
+
+static struct mipi_dsi_driver tianma_ta066vvhm03_driver = {
+	.probe = tianma_ta066vvhm03_probe,
+	.remove = tianma_ta066vvhm03_remove,
+	.driver = {
+		.name = "panel-tianma-ta066vvhm03",
+		.of_match_table = tianma_ta066vvhm03_of_match,
+	},
+};
+module_mipi_dsi_driver(tianma_ta066vvhm03_driver);
+
+MODULE_AUTHOR("Alexander Koskovich <akoskovich@pm.me>");
+MODULE_DESCRIPTION("DRM driver for Tianma TA066VVHM03-00");
+MODULE_LICENSE("GPL");

-- 
2.53.0

Re: [PATCH v3 2/2] drm/panel: Add support for Tianma TA066VVHM03 panel

[kernel test robot]

Hi Alexander,

kernel test robot noticed the following build errors:

[auto build test ERROR on 1f318b96cc84d7c2ab792fcc0bfd42a7ca890681]

url:    https://github.com/intel-lab-lkp/linux/commits/Alexander-Koskovich/dt-bindings-display-panel-Document-Tianma-TA066VVHM03/20260310-125055
base:   1f318b96cc84d7c2ab792fcc0bfd42a7ca890681
patch link:    https://lore.kernel.org/r/20260310-tianma-ta066vvhm03-v3-2-fc2938971d79%40pm.me
patch subject: [PATCH v3 2/2] drm/panel: Add support for Tianma TA066VVHM03 panel
config: arm64-randconfig-002-20260311 (https://download.01.org/0day-ci/archive/20260311/202603110640.rd02o2cM-lkp@intel.com/config)
compiler: clang version 23.0.0git (https://github.com/llvm/llvm-project 122f0b13a237b5024747b4ee99002590cc9a220a)
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20260311/202603110640.rd02o2cM-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202603110640.rd02o2cM-lkp@intel.com/

All errors (new ones prefixed by >>):

>> drivers/gpu/drm/panel/panel-tianma-ta066vvhm03.c:335:7: error: no member named 'dsc_slice_per_pkt' in 'struct mipi_dsi_device'
     335 |         dsi->dsc_slice_per_pkt = 2;
         |         ~~~  ^
   1 error generated.


vim +335 drivers/gpu/drm/panel/panel-tianma-ta066vvhm03.c

   286	
   287	static int tianma_ta066vvhm03_probe(struct mipi_dsi_device *dsi)
   288	{
   289		struct device *dev = &dsi->dev;
   290		struct tianma_ta066vvhm03 *ctx;
   291		int ret;
   292	
   293		ctx = devm_drm_panel_alloc(dev, struct tianma_ta066vvhm03, panel,
   294					   &tianma_ta066vvhm03_panel_funcs,
   295					   DRM_MODE_CONNECTOR_DSI);
   296		if (IS_ERR(ctx))
   297			return PTR_ERR(ctx);
   298	
   299		ret = devm_regulator_bulk_get_const(dev,
   300						    ARRAY_SIZE(tianma_ta066vvhm03_supplies),
   301						    tianma_ta066vvhm03_supplies,
   302						    &ctx->supplies);
   303		if (ret < 0)
   304			return ret;
   305	
   306		ctx->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
   307		if (IS_ERR(ctx->enable_gpio))
   308			return dev_err_probe(dev, PTR_ERR(ctx->enable_gpio),
   309					     "Failed to get enable-gpios\n");
   310	
   311		ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
   312		if (IS_ERR(ctx->reset_gpio))
   313			return dev_err_probe(dev, PTR_ERR(ctx->reset_gpio),
   314					     "Failed to get reset-gpios\n");
   315	
   316		ctx->dsi = dsi;
   317		mipi_dsi_set_drvdata(dsi, ctx);
   318	
   319		dsi->lanes = 4;
   320		dsi->format = MIPI_DSI_FMT_RGB888;
   321		dsi->mode_flags = MIPI_DSI_MODE_NO_EOT_PACKET |
   322				  MIPI_DSI_CLOCK_NON_CONTINUOUS;
   323	
   324		ctx->panel.prepare_prev_first = true;
   325	
   326		ctx->panel.backlight = tianma_ta066vvhm03_create_backlight(dsi);
   327		if (IS_ERR(ctx->panel.backlight))
   328			return dev_err_probe(dev, PTR_ERR(ctx->panel.backlight),
   329					     "Failed to create backlight\n");
   330	
   331		drm_panel_add(&ctx->panel);
   332	
   333		/* This panel only supports DSC; unconditionally enable it */
   334		dsi->dsc = &ctx->dsc;
 > 335		dsi->dsc_slice_per_pkt = 2;
   336	
   337		ctx->dsc.dsc_version_major = 1;
   338		ctx->dsc.dsc_version_minor = 1;
   339	
   340		ctx->dsc.slice_height = 20;
   341		ctx->dsc.slice_width = 540;
   342		WARN_ON(1080 % ctx->dsc.slice_width);
   343		ctx->dsc.slice_count = 1080 / ctx->dsc.slice_width;
   344		ctx->dsc.bits_per_component = 10;
   345		ctx->dsc.bits_per_pixel = 8 << 4; /* 4 fractional bits */
   346		ctx->dsc.block_pred_enable = true;
   347	
   348		ret = mipi_dsi_attach(dsi);
   349		if (ret < 0) {
   350			drm_panel_remove(&ctx->panel);
   351			return dev_err_probe(dev, ret, "Failed to attach to DSI host\n");
   352		}
   353	
   354		return 0;
   355	}
   356	

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki

Claude review: Add support for Tianma TA066VVHM03 DSI panel

[Claude Code Review Bot]

Overall Series Review

Subject: Add support for Tianma TA066VVHM03 DSI panel
Author: Alexander Koskovich <akoskovich@pm.me>
Patches: 4
Reviewed: 2026-03-11T13:40:04.084909

---

This is a straightforward 2-patch series adding a device tree binding and panel driver for the Tianma TA066VVHM03 6.59" 1080x2340 AMOLED DSI panel with DSC compression, found in the ASUS ROG Phone 3. The driver is generated with `linux-mdss-dsi-panel-driver-generator` and follows the modern patterns (using `devm_drm_panel_alloc`, `_multi` context for init sequences, `devm_regulator_bulk_get_const`). The DT binding already has Reviewed-by from Krzysztof Kozlowski.

The series has an external dependency on a pending `dsc_slice_per_pkt` patch (for `dsi->dsc_slice_per_pkt = 2`), which is correctly noted in the cover letter. The code is mostly clean but has a few issues, mainly around error handling in `prepare()`.

---
Generated by Claude Code Patch Reviewer

Claude review: dt-bindings: display: panel: Document Tianma TA066VVHM03

[Claude Code Review Bot]

Patch Review

This patch looks good. It already has `Reviewed-by: Krzysztof Kozlowski`.

One minor observation: `enable-gpios` is listed as an optional property (present in `properties` but not in `required`), which is consistent with how the driver handles it (via `devm_gpiod_get` which will fail if absent, so it's effectively required in the driver). It might be cleaner to either add it to `required` or make the driver use `devm_gpiod_get_optional` — but this is a minor consistency nit and the binding reviewer has already signed off.

No other issues.

---
Generated by Claude Code Patch Reviewer

Claude review: drm/panel: Add support for Tianma TA066VVHM03 panel

[Claude Code Review Bot]

Patch Review

**Issue 1 (bug): Missing cleanup in `prepare()` error paths for PPS/compression failures**

When `mipi_dsi_picture_parameter_set()` or `mipi_dsi_compression_mode()` fails, the function returns without undoing the work done by `tianma_ta066vvhm03_on()` (which sends DSI commands to the panel), without deasserting the reset/enable GPIOs, and without disabling regulators. Compare with the error path after `tianma_ta066vvhm03_on()` fails just above, which correctly cleans all of these up.

```c
	ret = mipi_dsi_picture_parameter_set(ctx->dsi, &pps);
	if (ret < 0) {
		dev_err(panel->dev, "failed to transmit PPS: %d\n", ret);
		return ret;  /* <-- leaks regulators, GPIOs, panel state */
	}

	ret = mipi_dsi_compression_mode(ctx->dsi, true);
	if (ret < 0) {
		dev_err(dev, "failed to enable compression mode: %d\n", ret);
		return ret;  /* <-- same leak */
	}
```

Additionally, the `_multi` variants (`mipi_dsi_picture_parameter_set_multi` and `mipi_dsi_compression_mode_multi`) are available in the current tree. The `prepare()` function could use a multi context throughout to simplify error handling — or at minimum, the error paths need to call the same cleanup as the `_on()` failure path (reset gpio, enable gpio, regulator disable).

**Issue 2 (minor): Inconsistent `dev` variable usage in `prepare()` error messages**

The PPS error path uses `panel->dev` while all other error paths use the local `dev` variable:

```c
		dev_err(panel->dev, "failed to transmit PPS: %d\n", ret);
```

vs:

```c
		dev_err(dev, "failed to enable compression mode: %d\n", ret);
```

Both refer to the same device, but using `panel->dev` here is inconsistent and unexpected. Should use `dev` for consistency.

**Issue 3 (dependency): `dsc_slice_per_pkt` field does not exist upstream**

```c
	dsi->dsc_slice_per_pkt = 2;
```

This field doesn't exist in `struct mipi_dsi_device` in the current tree. The cover letter correctly documents this dependency on a pending patch. This will prevent the driver from compiling until that dependency is merged. This is fine as long as the maintainer is aware and merges them in the right order.

**Issue 4 (minor nit): `WARN_ON` for a compile-time-knowable condition**

```c
	WARN_ON(1080 % ctx->dsc.slice_width);
```

Since `slice_width` is set to 540 just above, this is always false (1080 % 540 == 0). This is a runtime check for what is effectively a compile-time constant. It's harmless and used by other panel drivers (presumably a pattern from the generator), so no action strictly needed.

**Observation (style): The driver closely follows the `panel-raydium-rm692e5.c` pattern**

The overall structure, probe sequence, backlight handling, DSC setup, and remove function match the established patterns. The use of `devm_drm_panel_alloc`, `devm_regulator_bulk_get_const`, and `drm_connector_helper_get_modes_fixed` are all current best practices. Good.

**Summary for Patch 2:** The main issue to fix is the missing cleanup in the `prepare()` error paths after PPS/compression mode failures. Consider using the `_multi` variants for PPS and compression mode to simplify the control flow and ensure consistent error handling. Also fix the `panel->dev` vs `dev` inconsistency.

---
Generated by Claude Code Patch Reviewer