Re: [PATCH 1/2] dt-bindings:bridge Add LT7911EXC binding

[Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>]

ote, your message didn't reach dri-devel. Please check why. You might
need to switch to B4 Web relay submission, if there are any issues
with the SMTP on your side.

On Mon, 20 Apr 2026 at 05:34, <syyang@lontium.com> wrote:
>
> From: Sunyun Yang <syyang@lontium.com>
>
> -binding for lt7911exc.

Less is more, but here please settle for slightly more information
about the chip.

>
> Signed-off-by: Sunyun Yang <syyang@lontium.com>
> ---
>  .../display/bridge/lontium,lt7911exc.yaml     | 91 +++++++++++++++++++
>  1 file changed, 91 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/lontium,lt7911exc.yaml
>
> diff --git a/Documentation/devicetree/bindings/display/bridge/lontium,lt7911exc.yaml b/Documentation/devicetree/bindings/display/bridge/lontium,lt7911exc.yaml
> new file mode 100644
> index 000000000000..54a73d41635a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/lontium,lt7911exc.yaml
> @@ -0,0 +1,91 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/bridge/lontium,lt7911exc.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Lontium LT7911EXC eDP to MIPI Bridge
> +
> +maintainers:
> +  - Sunyun Yang <syyang@lontium.com>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - lontium,lt7911exc
> +
> +  reg:
> +    maxItems: 1
> +
> +  reset-gpios:
> +    maxItems: 1
> +    description: GPIO connected to RST_ pin.
> +
> +  vdd-supply:
> +    description: Regulator for 1.2V MIPI phy power.
> +
> +  vcc-supply:
> +    description: Regulator for 3.3V IO power.
> +
> +  ports:
> +    $ref: /schemas/graph.yaml#/properties/ports
> +
> +    properties:
> +      port@0:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description: Video port for mipi dsi output.

MIPI, DSI

> +
> +      port@1:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description: Video port for eDP input.
> +
> +    required:
> +      - port@0
> +      - port@1
> +
> +required:
> +  - compatible
> +  - reg
> +  - reset-gpios
> +  - vdd-supply
> +  - vcc-supply
> +  - ports
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        mipi-bridge@41 {
> +            compatible = "lontium,lt7911exc";
> +            reg = <0x41>;
> +            reset-gpios = <&gpy8 8 GPIO_ACTIVE_HIGH>;

Reset pins are usually active low.

> +            vdd-supply = <&lt7911exc_1v2>;
> +            vcc-supply = <&lt7911exc_3v3>;
> +
> +            ports {
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                port@0 {
> +                    reg = <0>;
> +
> +                    bridge_out: endpoint {
> +                        remote-endpoint = <&panel_in>;
> +                    };
> +                };
> +
> +                port@1 {
> +                    reg = <1>;
> +
> +                    bridge_in: endpoint {
> +                        remote-endpoint = <&edp_out>;
> +                    };
> +                };
> +            };
> +        };
> +    };

-- 
With best wishes
Dmitry