[PATCH 0/5] drm/bridge: Implement generic USB Type-C DP HPD bridge

[PATCH 0/5] drm/bridge: Implement generic USB Type-C DP HPD bridge

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

This series is split from the v15 "Add Type-C DP support for RK3399 EVB
IND board" series [1]. It focuses on the DRM bridge and Rockchip
platform CDN-DP controller changes.

[1] https://lore.kernel.org/all/20260304094152.92-1-kernel@airkyi.com/

====
1. Generic Type-C DP HPD bridge

Currently, several USB-C controller drivers register their own DP HPD
bridge via aux-hpd-bridge.c, each duplicating the same logic. For
devicetree based platforms, the USB-C controller may vary across boards,
and not every USB-C controller driver implements this feature. Patch 1
implements a generic DP HPD bridge that monitors Type-C bus events and
automatically creates an HPD bridge when a Type-C port device with DP
SVID is registered.

2. Multiple bridge model for CDN-DP

The RK3399 has two USB/DP combo PHY and one CDN-DP controller. Patch 5
introduces a multi-bridge model where each PHY port gets a separate
encoder and bridge, allowing flexible selection of the output PHY port.
This is based on the DRM AUX HPD bridge rather than extcon.

====
Patch 1 adds generic USB Type-C DP HPD bridge (Dmitry, Heikki).
Patch 2 adds new API drm_aux_bridge_register_from_node() (Neil).
Patch 3 adds DRM AUX bridge support for RK3399 USBDP PHY (Neil).
Patch 4 drops CDN-DP's extcon dependency when Type-C is present (Dmitry).
Patch 5 adds multiple bridges to support PHY port selection (Dmitry, Luca).

Chaoyi Chen (5):
  drm/bridge: Implement generic USB Type-C DP HPD bridge
  drm/bridge: aux: Add drm_aux_bridge_register_from_node()
  phy: rockchip: phy-rockchip-typec: Add DRM AUX bridge
  drm/rockchip: cdn-dp: Support handle lane info without extcon
  drm/rockchip: cdn-dp: Add multiple bridges to support PHY port
    selection

 drivers/gpu/drm/bridge/Kconfig                |  10 +
 drivers/gpu/drm/bridge/Makefile               |   1 +
 drivers/gpu/drm/bridge/aux-bridge.c           |  24 +-
 .../gpu/drm/bridge/aux-hpd-typec-dp-bridge.c  |  49 +++
 drivers/gpu/drm/rockchip/Kconfig              |   1 +
 drivers/gpu/drm/rockchip/cdn-dp-core.c        | 349 ++++++++++++++----
 drivers/gpu/drm/rockchip/cdn-dp-core.h        |  18 +-
 drivers/phy/rockchip/Kconfig                  |   2 +
 drivers/phy/rockchip/phy-rockchip-typec.c     |  13 +-
 include/drm/bridge/aux-bridge.h               |   6 +
 10 files changed, 404 insertions(+), 69 deletions(-)
 create mode 100644 drivers/gpu/drm/bridge/aux-hpd-typec-dp-bridge.c

-- 
2.53.0

[PATCH 1/5] drm/bridge: Implement generic USB Type-C DP HPD bridge

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

The HPD function of Type-C DP is implemented through
drm_connector_oob_hotplug_event(). For embedded DP, it is required
that the DRM connector fwnode corresponds to the Type-C port fwnode.

To describe the relationship between the DP controller and the Type-C
port device, we usually using drm_bridge to build a bridge chain.

Now several USB-C controller drivers have already implemented the DP
HPD bridge function provided by aux-hpd-bridge.c, it will build a DP
HPD bridge on USB-C connector port device.

But this requires the USB-C controller driver to manually register the
HPD bridge. If the driver does not implement this feature, the bridge
will not be create.

So this patch implements a generic DP HPD bridge based on
aux-hpd-bridge.c. It will monitor Type-C bus events, and when a
Type-C port device containing the DP svid is registered, it will
create an HPD bridge for it without the need for the USB-C controller
driver to implement it.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---
 drivers/gpu/drm/bridge/Kconfig                | 10 ++++
 drivers/gpu/drm/bridge/Makefile               |  1 +
 .../gpu/drm/bridge/aux-hpd-typec-dp-bridge.c  | 49 +++++++++++++++++++
 3 files changed, 60 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/aux-hpd-typec-dp-bridge.c

diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index c3209b0f4678..d92e93875793 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -30,6 +30,16 @@ config DRM_AUX_HPD_BRIDGE
 	  Simple bridge that terminates the bridge chain and provides HPD
 	  support.
 
+if DRM_AUX_HPD_BRIDGE
+config DRM_AUX_HPD_TYPEC_BRIDGE
+	tristate
+	depends on TYPEC || !TYPEC
+	default TYPEC
+	help
+	  Simple bridge that terminates the bridge chain and provides HPD
+	  support. It build bridge on each USB-C connector device node.
+endif
+
 menu "Display Interface Bridges"
 	depends on DRM && DRM_BRIDGE
 
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index beab5b695a6e..c4761526ba0a 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_DRM_AUX_BRIDGE) += aux-bridge.o
 obj-$(CONFIG_DRM_AUX_HPD_BRIDGE) += aux-hpd-bridge.o
+obj-$(CONFIG_DRM_AUX_HPD_TYPEC_BRIDGE) += aux-hpd-typec-dp-bridge.o
 obj-$(CONFIG_DRM_CHIPONE_ICN6211) += chipone-icn6211.o
 obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o
 obj-$(CONFIG_DRM_CROS_EC_ANX7688) += cros-ec-anx7688.o
diff --git a/drivers/gpu/drm/bridge/aux-hpd-typec-dp-bridge.c b/drivers/gpu/drm/bridge/aux-hpd-typec-dp-bridge.c
new file mode 100644
index 000000000000..d915e0fb0668
--- /dev/null
+++ b/drivers/gpu/drm/bridge/aux-hpd-typec-dp-bridge.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0+
+#include <linux/of.h>
+#include <linux/usb/typec_altmode.h>
+#include <linux/usb/typec_dp.h>
+
+#include <drm/bridge/aux-bridge.h>
+
+static int drm_typec_bus_event(struct notifier_block *nb,
+			       unsigned long action, void *data)
+{
+	struct device *dev = (struct device *)data;
+	struct typec_altmode *alt = to_typec_altmode(dev);
+
+	if (action != BUS_NOTIFY_ADD_DEVICE)
+		goto done;
+
+	/*
+	 * alt->dev.parent->parent : USB-C controller device
+	 * alt->dev.parent         : USB-C connector device
+	 */
+	if (is_typec_port_altmode(&alt->dev) && alt->svid == USB_TYPEC_DP_SID)
+		drm_dp_hpd_bridge_register(alt->dev.parent->parent,
+					   to_of_node(alt->dev.parent->fwnode));
+
+done:
+	return NOTIFY_OK;
+}
+
+static struct notifier_block drm_typec_event_nb = {
+	.notifier_call = drm_typec_bus_event,
+};
+
+static void drm_aux_hpd_typec_dp_bridge_module_exit(void)
+{
+	bus_unregister_notifier(&typec_bus, &drm_typec_event_nb);
+}
+
+static int __init drm_aux_hpd_typec_dp_bridge_module_init(void)
+{
+	bus_register_notifier(&typec_bus, &drm_typec_event_nb);
+
+	return 0;
+}
+
+module_init(drm_aux_hpd_typec_dp_bridge_module_init);
+module_exit(drm_aux_hpd_typec_dp_bridge_module_exit);
+
+MODULE_DESCRIPTION("DRM TYPEC DP HPD BRIDGE");
+MODULE_LICENSE("GPL");
-- 
2.53.0

[PATCH 2/5] drm/bridge: aux: Add drm_aux_bridge_register_from_node()

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

The drm_aux_bridge_register() uses the device->of_node as the
bridge->of_node.

This patch adds drm_aux_bridge_register_from_node() to allow
specifying the of_node corresponding to the bridge.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/gpu/drm/bridge/aux-bridge.c | 24 ++++++++++++++++++++++--
 include/drm/bridge/aux-bridge.h     |  6 ++++++
 2 files changed, 28 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/bridge/aux-bridge.c b/drivers/gpu/drm/bridge/aux-bridge.c
index 1ed21a8713bf..f50283abed5f 100644
--- a/drivers/gpu/drm/bridge/aux-bridge.c
+++ b/drivers/gpu/drm/bridge/aux-bridge.c
@@ -35,6 +35,7 @@ static void drm_aux_bridge_unregister_adev(void *_adev)
 /**
  * drm_aux_bridge_register - Create a simple bridge device to link the chain
  * @parent: device instance providing this bridge
+ * @np: device node pointer corresponding to this bridge instance
  *
  * Creates a simple DRM bridge that doesn't implement any drm_bridge
  * operations. Such bridges merely fill a place in the bridge chain linking
@@ -42,7 +43,7 @@ static void drm_aux_bridge_unregister_adev(void *_adev)
  *
  * Return: zero on success, negative error code on failure
  */
-int drm_aux_bridge_register(struct device *parent)
+int drm_aux_bridge_register_from_node(struct device *parent, struct device_node *np)
 {
 	struct auxiliary_device *adev;
 	int ret;
@@ -62,7 +63,10 @@ int drm_aux_bridge_register(struct device *parent)
 	adev->dev.parent = parent;
 	adev->dev.release = drm_aux_bridge_release;
 
-	device_set_of_node_from_dev(&adev->dev, parent);
+	if (np)
+		device_set_node(&adev->dev, of_fwnode_handle(np));
+	else
+		device_set_of_node_from_dev(&adev->dev, parent);
 
 	ret = auxiliary_device_init(adev);
 	if (ret) {
@@ -80,6 +84,22 @@ int drm_aux_bridge_register(struct device *parent)
 
 	return devm_add_action_or_reset(parent, drm_aux_bridge_unregister_adev, adev);
 }
+EXPORT_SYMBOL_GPL(drm_aux_bridge_register_from_node);
+
+/**
+ * drm_aux_bridge_register - Create a simple bridge device to link the chain
+ * @parent: device instance providing this bridge
+ *
+ * Creates a simple DRM bridge that doesn't implement any drm_bridge
+ * operations. Such bridges merely fill a place in the bridge chain linking
+ * surrounding DRM bridges.
+ *
+ * Return: zero on success, negative error code on failure
+ */
+int drm_aux_bridge_register(struct device *parent)
+{
+	return drm_aux_bridge_register_from_node(parent, NULL);
+}
 EXPORT_SYMBOL_GPL(drm_aux_bridge_register);
 
 struct drm_aux_bridge_data {
diff --git a/include/drm/bridge/aux-bridge.h b/include/drm/bridge/aux-bridge.h
index c2f5a855512f..7dd1f17a1354 100644
--- a/include/drm/bridge/aux-bridge.h
+++ b/include/drm/bridge/aux-bridge.h
@@ -13,11 +13,17 @@ struct auxiliary_device;
 
 #if IS_ENABLED(CONFIG_DRM_AUX_BRIDGE)
 int drm_aux_bridge_register(struct device *parent);
+int drm_aux_bridge_register_from_node(struct device *parent, struct device_node *np);
 #else
 static inline int drm_aux_bridge_register(struct device *parent)
 {
 	return 0;
 }
+
+static inline int drm_aux_bridge_register_from_node(struct device *parent, struct device_node *np)
+{
+	return 0;
+}
 #endif
 
 #if IS_ENABLED(CONFIG_DRM_AUX_HPD_BRIDGE)
-- 
2.53.0

[PATCH 3/5] phy: rockchip: phy-rockchip-typec: Add DRM AUX bridge

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

Using the DRM_AUX_BRIDGE helper to create the transparent DRM bridge
device.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/phy/rockchip/Kconfig              |  2 ++
 drivers/phy/rockchip/phy-rockchip-typec.c | 13 +++++++++++--
 2 files changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig
index 14698571b607..9173d3b4fef4 100644
--- a/drivers/phy/rockchip/Kconfig
+++ b/drivers/phy/rockchip/Kconfig
@@ -119,6 +119,8 @@ config PHY_ROCKCHIP_SNPS_PCIE3
 config PHY_ROCKCHIP_TYPEC
 	tristate "Rockchip TYPEC PHY Driver"
 	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
+	depends on DRM || DRM=n
+	select DRM_AUX_BRIDGE if DRM_BRIDGE
 	select EXTCON
 	select GENERIC_PHY
 	select RESET_CONTROLLER
diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c
index d9701b6106d5..48070b50416e 100644
--- a/drivers/phy/rockchip/phy-rockchip-typec.c
+++ b/drivers/phy/rockchip/phy-rockchip-typec.c
@@ -54,6 +54,7 @@
 
 #include <linux/mfd/syscon.h>
 #include <linux/phy/phy.h>
+#include <drm/bridge/aux-bridge.h>
 
 #define CMN_SSM_BANDGAP			(0x21 << 2)
 #define CMN_SSM_BIAS			(0x22 << 2)
@@ -1162,16 +1163,24 @@ static int rockchip_typec_phy_probe(struct platform_device *pdev)
 
 	for_each_available_child_of_node(np, child_np) {
 		struct phy *phy;
+		ret = 0;
 
-		if (of_node_name_eq(child_np, "dp-port"))
+		if (of_node_name_eq(child_np, "dp-port")) {
 			phy = devm_phy_create(dev, child_np,
 					      &rockchip_dp_phy_ops);
-		else if (of_node_name_eq(child_np, "usb3-port"))
+			ret = drm_aux_bridge_register_from_node(dev, child_np);
+		} else if (of_node_name_eq(child_np, "usb3-port"))
 			phy = devm_phy_create(dev, child_np,
 					      &rockchip_usb3_phy_ops);
 		else
 			continue;
 
+		if (ret) {
+			pm_runtime_disable(dev);
+			of_node_put(child_np);
+			return ret;
+		}
+
 		if (IS_ERR(phy)) {
 			dev_err(dev, "failed to create phy: %pOFn\n",
 				child_np);
-- 
2.53.0

[PATCH 4/5] drm/rockchip: cdn-dp: Support handle lane info without extcon

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

This patch add support for get PHY lane info without help of extcon.

There is no extcon needed if the Type-C controller is present. In this
case, the lane info can be get from PHY instead of extcon.

The extcon device should still be supported if Type-C controller is
not present.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---
 drivers/gpu/drm/rockchip/cdn-dp-core.c | 25 +++++++++++++++++--------
 1 file changed, 17 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.c b/drivers/gpu/drm/rockchip/cdn-dp-core.c
index 177e30445ee8..9068118859e2 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.c
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.c
@@ -157,6 +157,9 @@ static int cdn_dp_get_port_lanes(struct cdn_dp_port *port)
 	int dptx;
 	u8 lanes;
 
+	if (!edev)
+		return phy_get_bus_width(port->phy);
+
 	dptx = extcon_get_state(edev, EXTCON_DISP_DP);
 	if (dptx > 0) {
 		extcon_get_property(edev, EXTCON_DISP_DP,
@@ -220,7 +223,7 @@ static bool cdn_dp_check_sink_connection(struct cdn_dp_device *dp)
 	 * some docks need more time to power up.
 	 */
 	while (time_before(jiffies, timeout)) {
-		if (!extcon_get_state(port->extcon, EXTCON_DISP_DP))
+		if (port->extcon && !extcon_get_state(port->extcon, EXTCON_DISP_DP))
 			return false;
 
 		if (!cdn_dp_get_sink_count(dp, &sink_count))
@@ -386,11 +389,14 @@ static int cdn_dp_enable_phy(struct cdn_dp_device *dp, struct cdn_dp_port *port)
 		goto err_power_on;
 	}
 
-	ret = extcon_get_property(port->extcon, EXTCON_DISP_DP,
-				  EXTCON_PROP_USB_TYPEC_POLARITY, &property);
-	if (ret) {
-		DRM_DEV_ERROR(dp->dev, "get property failed\n");
-		goto err_power_on;
+	property.intval = 0;
+	if (port->extcon) {
+		ret = extcon_get_property(port->extcon, EXTCON_DISP_DP,
+					  EXTCON_PROP_USB_TYPEC_POLARITY, &property);
+		if (ret) {
+			DRM_DEV_ERROR(dp->dev, "get property failed\n");
+			goto err_power_on;
+		}
 	}
 
 	port->lanes = cdn_dp_get_port_lanes(port);
@@ -1029,6 +1035,9 @@ static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
 	for (i = 0; i < dp->ports; i++) {
 		port = dp->port[i];
 
+		if (!port->extcon)
+			continue;
+
 		port->event_nb.notifier_call = cdn_dp_pd_event;
 		ret = devm_extcon_register_notifier(dp->dev, port->extcon,
 						    EXTCON_DISP_DP,
@@ -1121,14 +1130,14 @@ static int cdn_dp_probe(struct platform_device *pdev)
 		    PTR_ERR(phy) == -EPROBE_DEFER)
 			return -EPROBE_DEFER;
 
-		if (IS_ERR(extcon) || IS_ERR(phy))
+		if (IS_ERR(phy) || PTR_ERR(extcon) != -ENODEV)
 			continue;
 
 		port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
 		if (!port)
 			return -ENOMEM;
 
-		port->extcon = extcon;
+		port->extcon = IS_ERR(extcon) ? NULL : extcon;
 		port->phy = phy;
 		port->dp = dp;
 		port->id = i;
-- 
2.53.0

[PATCH 5/5] drm/rockchip: cdn-dp: Add multiple bridges to support PHY port selection

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

The RK3399 has two USB/DP combo PHY and one CDN-DP controller. And
the CDN-DP can be switched to output to one of the PHYs. If both ports
are plugged into DP, DP will select the first port for output.

This patch adds support for multiple bridges, enabling users to flexibly
select the output port. For each PHY port, a separate encoder and bridge
are registered.

The change is based on the DRM AUX HPD bridge, rather than the
extcon approach. This requires the DT to correctly describe the
connections between the first bridge in bridge chain and DP
controller. For example, the bridge chain may be like this:

PHY aux birdge -> fsa4480 analog audio switch bridge ->
onnn,nb7vpq904m USB reminder bridge -> USB-C controller AUX HPD bridge

In this case, the connection relationships among the PHY aux bridge
and the DP contorller need to be described in DT.

In addition, the cdn_dp_parse_next_bridge_dt() will parses it and
determines whether to register one or two bridges.

Since there is only one DP controller, only one of the PHY ports can
output at a time. The key is how to switch between different PHYs,
which is handled by cdn_dp_switch_port() and cdn_dp_enable().

There are two cases:

1. Neither bridge is enabled. In this case, both bridges can
independently read the EDID, and the PHY port may switch before
reading the EDID.

2. One bridge is already enabled. In this case, other bridges are not
allowed to read the EDID. So we will try to return the cached EDID.

Since the scenario of two ports plug in at the same time is rare,
I don't have a board which support two TypeC connector to test this.
Therefore, I tested forced switching on a single PHY port, as well as
output using a fake PHY port alongside a real PHY port.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---
 drivers/gpu/drm/rockchip/Kconfig       |   1 +
 drivers/gpu/drm/rockchip/cdn-dp-core.c | 324 ++++++++++++++++++++-----
 drivers/gpu/drm/rockchip/cdn-dp-core.h |  18 +-
 3 files changed, 286 insertions(+), 57 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/Kconfig b/drivers/gpu/drm/rockchip/Kconfig
index 1479b8c4ed40..cb97690c5a5d 100644
--- a/drivers/gpu/drm/rockchip/Kconfig
+++ b/drivers/gpu/drm/rockchip/Kconfig
@@ -59,6 +59,7 @@ config ROCKCHIP_CDN_DP
 	select DRM_DISPLAY_HELPER
 	select DRM_BRIDGE_CONNECTOR
 	select DRM_DISPLAY_DP_HELPER
+	select DRM_AUX_HPD_BRIDGE
 	help
 	  This selects support for Rockchip SoC specific extensions
 	  for the cdn DP driver. If you want to enable Dp on
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.c b/drivers/gpu/drm/rockchip/cdn-dp-core.c
index 9068118859e2..b9ba279ca653 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.c
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.c
@@ -28,16 +28,17 @@
 #include "cdn-dp-core.h"
 #include "cdn-dp-reg.h"
 
-static inline struct cdn_dp_device *bridge_to_dp(struct drm_bridge *bridge)
+static int cdn_dp_switch_port(struct cdn_dp_device *dp, struct cdn_dp_port *prev_port,
+			      struct cdn_dp_port *port);
+
+static inline struct cdn_dp_bridge *bridge_to_dp_bridge(struct drm_bridge *bridge)
 {
-	return container_of(bridge, struct cdn_dp_device, bridge);
+	return container_of(bridge, struct cdn_dp_bridge, bridge);
 }
 
-static inline struct cdn_dp_device *encoder_to_dp(struct drm_encoder *encoder)
+static inline struct cdn_dp_device *bridge_to_dp(struct drm_bridge *bridge)
 {
-	struct rockchip_encoder *rkencoder = to_rockchip_encoder(encoder);
-
-	return container_of(rkencoder, struct cdn_dp_device, encoder);
+	return bridge_to_dp_bridge(bridge)->parent;
 }
 
 #define GRF_SOC_CON9		0x6224
@@ -192,14 +193,27 @@ static int cdn_dp_get_sink_count(struct cdn_dp_device *dp, u8 *sink_count)
 static struct cdn_dp_port *cdn_dp_connected_port(struct cdn_dp_device *dp)
 {
 	struct cdn_dp_port *port;
-	int i, lanes;
+	int i, lanes[MAX_PHY];
 
 	for (i = 0; i < dp->ports; i++) {
 		port = dp->port[i];
-		lanes = cdn_dp_get_port_lanes(port);
-		if (lanes)
+		lanes[i] = cdn_dp_get_port_lanes(port);
+		if (!dp->next_bridge_valid)
 			return port;
 	}
+
+	if (dp->next_bridge_valid) {
+		/* If more than one port is available, pick the last active port */
+		if (dp->active_port > 0 && lanes[dp->active_port])
+			return dp->port[dp->active_port];
+
+		/* If the last active port is not available, pick an available port in order */
+		for (i = 0; i < dp->bridge_count; i++) {
+			if (lanes[i])
+				return dp->port[i];
+		}
+	}
+
 	return NULL;
 }
 
@@ -254,12 +268,45 @@ static const struct drm_edid *
 cdn_dp_bridge_edid_read(struct drm_bridge *bridge, struct drm_connector *connector)
 {
 	struct cdn_dp_device *dp = bridge_to_dp(bridge);
-	const struct drm_edid *drm_edid;
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
+	struct cdn_dp_port *port = dp->port[dp_bridge->id];
+	struct cdn_dp_port *prev_port;
+	const struct drm_edid *drm_edid = NULL;
+	int i, ret;
 
 	mutex_lock(&dp->lock);
+
+	/* More than one port is available */
+	if (dp->bridge_count > 1 && !port->phy_enabled) {
+		for (i = 0; i < dp->bridge_count; i++) {
+			/* Another port already enable */
+			if (dp->bridge_list[i] != dp_bridge && dp->bridge_list[i]->enabled)
+				goto get_cache;
+			/* Find already enabled port */
+			if (dp->port[i]->phy_enabled)
+				prev_port = dp->port[i];
+		}
+
+		/* Switch to current port */
+		if (prev_port) {
+			ret = cdn_dp_switch_port(dp, prev_port, port);
+			if (ret)
+				goto get_cache;
+		}
+	}
+
 	drm_edid = drm_edid_read_custom(connector, cdn_dp_get_edid_block, dp);
+	/* replace edid cache */
+	if (dp->edid_cache[dp_bridge->id])
+		drm_edid_free(dp->edid_cache[dp_bridge->id]);
+	dp->edid_cache[dp_bridge->id] = drm_edid_dup(drm_edid);
+
 	mutex_unlock(&dp->lock);
+	return drm_edid;
 
+get_cache:
+	drm_edid = drm_edid_dup(dp->edid_cache[dp_bridge->id]);
+	mutex_unlock(&dp->lock);
 	return drm_edid;
 }
 
@@ -268,12 +315,13 @@ cdn_dp_bridge_mode_valid(struct drm_bridge *bridge,
 			 const struct drm_display_info *display_info,
 			 const struct drm_display_mode *mode)
 {
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
 	struct cdn_dp_device *dp = bridge_to_dp(bridge);
 	u32 requested, actual, rate, sink_max, source_max = 0;
 	u8 lanes, bpc;
 
 	/* If DP is disconnected, every mode is invalid */
-	if (!dp->connected)
+	if (!dp_bridge->connected || !dp->connected)
 		return MODE_BAD;
 
 	switch (display_info->bpc) {
@@ -551,6 +599,54 @@ static bool cdn_dp_check_link_status(struct cdn_dp_device *dp)
 	return drm_dp_channel_eq_ok(link_status, min(port->lanes, sink_lanes));
 }
 
+static int cdn_dp_switch_port(struct cdn_dp_device *dp, struct cdn_dp_port *prev_port,
+			      struct cdn_dp_port *port)
+{
+	int ret;
+
+	if (dp->active)
+		return 0;
+
+	ret = cdn_dp_disable_phy(dp, prev_port);
+	if (ret)
+		goto out;
+	ret = cdn_dp_enable_phy(dp, port);
+	if (ret)
+		goto out;
+
+	ret = cdn_dp_get_sink_capability(dp);
+	if (ret) {
+		cdn_dp_disable_phy(dp, port);
+		goto out;
+	}
+
+	dp->active = true;
+	dp->lanes = port->lanes;
+
+	if (!cdn_dp_check_link_status(dp)) {
+		dev_info(dp->dev, "Connected with sink; re-train link\n");
+
+		ret = cdn_dp_train_link(dp);
+		if (ret) {
+			dev_err(dp->dev, "Training link failed: %d\n", ret);
+			goto out;
+		}
+
+		ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_IDLE);
+		if (ret) {
+			dev_err(dp->dev, "Failed to idle video %d\n", ret);
+			goto out;
+		}
+
+		ret = cdn_dp_config_video(dp);
+		if (ret)
+			dev_err(dp->dev, "Failed to configure video: %d\n", ret);
+	}
+
+out:
+	return ret;
+}
+
 static void cdn_dp_display_info_update(struct cdn_dp_device *dp,
 				       struct drm_display_info *display_info)
 {
@@ -572,6 +668,7 @@ static void cdn_dp_display_info_update(struct cdn_dp_device *dp,
 static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_atomic_state *state)
 {
 	struct cdn_dp_device *dp = bridge_to_dp(bridge);
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
 	struct drm_connector *connector;
 	int ret, val;
 
@@ -581,7 +678,7 @@ static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_at
 
 	cdn_dp_display_info_update(dp, &connector->display_info);
 
-	ret = drm_of_encoder_active_endpoint_id(dp->dev->of_node, &dp->encoder.encoder);
+	ret = drm_of_encoder_active_endpoint_id(dp->dev->of_node, &dp_bridge->encoder.encoder);
 	if (ret < 0) {
 		DRM_DEV_ERROR(dp->dev, "Could not get vop id, %d", ret);
 		return;
@@ -600,6 +697,9 @@ static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_at
 
 	mutex_lock(&dp->lock);
 
+	if (dp->next_bridge_valid)
+		dp->active_port = dp_bridge->id;
+
 	ret = cdn_dp_enable(dp);
 	if (ret) {
 		DRM_DEV_ERROR(dp->dev, "Failed to enable bridge %d\n",
@@ -632,6 +732,7 @@ static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_at
 		goto out;
 	}
 
+	dp_bridge->enabled = true;
 out:
 	mutex_unlock(&dp->lock);
 }
@@ -639,9 +740,11 @@ static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_at
 static void cdn_dp_bridge_atomic_disable(struct drm_bridge *bridge, struct drm_atomic_state *state)
 {
 	struct cdn_dp_device *dp = bridge_to_dp(bridge);
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
 	int ret;
 
 	mutex_lock(&dp->lock);
+	dp_bridge->enabled = false;
 
 	if (dp->active) {
 		ret = cdn_dp_disable(dp);
@@ -828,6 +931,16 @@ static int cdn_dp_audio_mute_stream(struct drm_bridge *bridge,
 	return ret;
 }
 
+static void cdn_dp_bridge_hpd_notify(struct drm_bridge *bridge,
+			   enum drm_connector_status status)
+{
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
+	struct cdn_dp_device *dp = bridge_to_dp(bridge);
+
+	dp->bridge_list[dp_bridge->id]->connected = status == connector_status_connected;
+	schedule_work(&dp->event_work);
+}
+
 static const struct drm_bridge_funcs cdn_dp_bridge_funcs = {
 	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
 	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
@@ -838,6 +951,7 @@ static const struct drm_bridge_funcs cdn_dp_bridge_funcs = {
 	.atomic_disable = cdn_dp_bridge_atomic_disable,
 	.mode_valid = cdn_dp_bridge_mode_valid,
 	.mode_set = cdn_dp_bridge_mode_set,
+	.hpd_notify = cdn_dp_bridge_hpd_notify,
 
 	.dp_audio_prepare = cdn_dp_audio_prepare,
 	.dp_audio_mute_stream = cdn_dp_audio_mute_stream,
@@ -886,7 +1000,8 @@ static void cdn_dp_pd_event_work(struct work_struct *work)
 {
 	struct cdn_dp_device *dp = container_of(work, struct cdn_dp_device,
 						event_work);
-	int ret;
+	bool connected;
+	int i, ret;
 
 	mutex_lock(&dp->lock);
 
@@ -945,9 +1060,12 @@ static void cdn_dp_pd_event_work(struct work_struct *work)
 
 out:
 	mutex_unlock(&dp->lock);
-	drm_bridge_hpd_notify(&dp->bridge,
-			      dp->connected ? connector_status_connected
-					    : connector_status_disconnected);
+	for (i = 0; i < dp->bridge_count; i++) {
+		connected = dp->connected && dp->bridge_list[i]->connected;
+		drm_bridge_hpd_notify(&dp->bridge_list[i]->bridge,
+				      connected ? connector_status_connected
+						: connector_status_disconnected);
+	}
 }
 
 static int cdn_dp_pd_event(struct notifier_block *nb,
@@ -967,28 +1085,16 @@ static int cdn_dp_pd_event(struct notifier_block *nb,
 	return NOTIFY_DONE;
 }
 
-static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
+static int cdn_bridge_add(struct device *dev,
+			  struct drm_bridge *bridge,
+			  struct drm_bridge *next_bridge,
+			  struct drm_encoder *encoder)
 {
 	struct cdn_dp_device *dp = dev_get_drvdata(dev);
-	struct drm_encoder *encoder;
+	struct drm_device *drm_dev = dp->drm_dev;
+	struct drm_bridge *last_bridge __free(drm_bridge_put) = NULL;
 	struct drm_connector *connector;
-	struct cdn_dp_port *port;
-	struct drm_device *drm_dev = data;
-	int ret, i;
-
-	ret = cdn_dp_parse_dt(dp);
-	if (ret < 0)
-		return ret;
-
-	dp->drm_dev = drm_dev;
-	dp->connected = false;
-	dp->active = false;
-	dp->active_port = -1;
-	dp->fw_loaded = false;
-
-	INIT_WORK(&dp->event_work, cdn_dp_pd_event_work);
-
-	encoder = &dp->encoder.encoder;
+	int ret;
 
 	encoder->possible_crtcs = drm_of_find_possible_crtcs(drm_dev,
 							     dev->of_node);
@@ -1003,26 +1109,35 @@ static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
 
 	drm_encoder_helper_add(encoder, &cdn_dp_encoder_helper_funcs);
 
-	dp->bridge.ops =
-			DRM_BRIDGE_OP_DETECT |
-			DRM_BRIDGE_OP_EDID |
-			DRM_BRIDGE_OP_HPD |
-			DRM_BRIDGE_OP_DP_AUDIO;
-	dp->bridge.of_node = dp->dev->of_node;
-	dp->bridge.type = DRM_MODE_CONNECTOR_DisplayPort;
-	dp->bridge.hdmi_audio_dev = dp->dev;
-	dp->bridge.hdmi_audio_max_i2s_playback_channels = 8;
-	dp->bridge.hdmi_audio_spdif_playback = 1;
-	dp->bridge.hdmi_audio_dai_port = -1;
-
-	ret = devm_drm_bridge_add(dev, &dp->bridge);
+	bridge->ops =
+		DRM_BRIDGE_OP_DETECT |
+		DRM_BRIDGE_OP_EDID |
+		DRM_BRIDGE_OP_HPD |
+		DRM_BRIDGE_OP_DP_AUDIO;
+	bridge->of_node = dp->dev->of_node;
+	bridge->type = DRM_MODE_CONNECTOR_DisplayPort;
+	bridge->hdmi_audio_dev = dp->dev;
+	bridge->hdmi_audio_max_i2s_playback_channels = 8;
+	bridge->hdmi_audio_spdif_playback = 1;
+	bridge->hdmi_audio_dai_port = -1;
+
+	ret = devm_drm_bridge_add(dev, bridge);
 	if (ret)
 		return ret;
 
-	ret = drm_bridge_attach(encoder, &dp->bridge, NULL, DRM_BRIDGE_ATTACH_NO_CONNECTOR);
+	ret = drm_bridge_attach(encoder, bridge, NULL, DRM_BRIDGE_ATTACH_NO_CONNECTOR);
 	if (ret)
 		return ret;
 
+	if (next_bridge) {
+		ret = drm_bridge_attach(encoder, next_bridge, bridge,
+					DRM_BRIDGE_ATTACH_NO_CONNECTOR);
+		if (ret)
+			return ret;
+
+		last_bridge = drm_bridge_chain_get_last_bridge(bridge->encoder);
+	}
+
 	connector = drm_bridge_connector_init(drm_dev, encoder);
 	if (IS_ERR(connector)) {
 		ret = PTR_ERR(connector);
@@ -1030,8 +1145,99 @@ static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
 		return ret;
 	}
 
+	if (last_bridge)
+		connector->fwnode = fwnode_handle_get(of_fwnode_handle(last_bridge->of_node));
+
 	drm_connector_attach_encoder(connector, encoder);
 
+	return 0;
+}
+
+static int cdn_dp_parse_next_bridge_dt(struct cdn_dp_device *dp)
+{
+	struct device_node *np = dp->dev->of_node;
+	struct device_node *port __free(device_node) = of_graph_get_port_by_id(np, 1);
+	struct drm_bridge *bridge;
+	int count = 0;
+	int ret = 0;
+	int i;
+
+	/* If device use extcon, do not use hpd bridge */
+	for (i = 0; i < dp->ports; i++) {
+		if (dp->port[i]->extcon) {
+			dp->bridge_count = 1;
+			return 0;
+		}
+	}
+
+	/* One endpoint may correspond to one next bridge. */
+	for_each_of_graph_port_endpoint(port, dp_ep) {
+		struct device_node *next_bridge_node __free(device_node) =
+			of_graph_get_remote_port_parent(dp_ep);
+
+		bridge = of_drm_find_bridge(next_bridge_node);
+		if (!bridge) {
+			ret = -EPROBE_DEFER;
+			goto out;
+		}
+
+		dp->next_bridge_valid = true;
+		dp->next_bridge_list[count] = drm_bridge_get(bridge);
+		count++;
+	}
+
+out:
+	dp->bridge_count = count ? count : 1;
+	return ret;
+}
+
+static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
+{
+	struct cdn_dp_device *dp = dev_get_drvdata(dev);
+	struct drm_bridge *bridge, *next_bridge;
+	struct drm_encoder *encoder;
+	struct cdn_dp_port *port;
+	struct drm_device *drm_dev = data;
+	struct cdn_dp_bridge *dp_bridge;
+	int ret, i;
+
+	ret = cdn_dp_parse_dt(dp);
+	if (ret < 0)
+		return ret;
+
+	ret = cdn_dp_parse_next_bridge_dt(dp);
+	if (ret)
+		return ret;
+
+	dp->drm_dev = drm_dev;
+	dp->connected = false;
+	dp->active = false;
+	dp->active_port = -1;
+	dp->fw_loaded = false;
+
+	for (i = 0; i < dp->bridge_count; i++) {
+		dp_bridge = devm_drm_bridge_alloc(dev, struct cdn_dp_bridge, bridge,
+						    &cdn_dp_bridge_funcs);
+		if (IS_ERR(dp_bridge))
+			return PTR_ERR(dp_bridge);
+		dp_bridge->id = i;
+		dp_bridge->parent = dp;
+		if (!dp->next_bridge_valid)
+			dp_bridge->connected = true;
+		dp->bridge_list[i] = dp_bridge;
+	}
+
+	for (i = 0; i < dp->bridge_count; i++) {
+		encoder = &dp->bridge_list[i]->encoder.encoder;
+		bridge = &dp->bridge_list[i]->bridge;
+		next_bridge = dp->next_bridge_list[i];
+		ret = cdn_bridge_add(dev, bridge, next_bridge, encoder);
+		if (ret)
+			return ret;
+	}
+
+	INIT_WORK(&dp->event_work, cdn_dp_pd_event_work);
+
 	for (i = 0; i < dp->ports; i++) {
 		port = dp->port[i];
 
@@ -1059,10 +1265,18 @@ static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
 static void cdn_dp_unbind(struct device *dev, struct device *master, void *data)
 {
 	struct cdn_dp_device *dp = dev_get_drvdata(dev);
-	struct drm_encoder *encoder = &dp->encoder.encoder;
+	struct drm_encoder *encoder;
+	int i;
 
 	cancel_work_sync(&dp->event_work);
-	encoder->funcs->destroy(encoder);
+	for (i = 0; i < dp->bridge_count; i++) {
+		encoder = &dp->bridge_list[i]->encoder.encoder;
+		encoder->funcs->destroy(encoder);
+		drm_bridge_put(dp->next_bridge_list[i]);
+	}
+
+	for (i = 0; i < MAX_PHY; i++)
+		drm_edid_free(dp->edid_cache[i]);
 
 	pm_runtime_disable(dev);
 	if (dp->fw_loaded)
@@ -1113,10 +1327,10 @@ static int cdn_dp_probe(struct platform_device *pdev)
 	int ret;
 	int i;
 
-	dp = devm_drm_bridge_alloc(dev, struct cdn_dp_device, bridge,
-				   &cdn_dp_bridge_funcs);
-	if (IS_ERR(dp))
-		return PTR_ERR(dp);
+	dp = devm_kzalloc(dev, sizeof(*dp), GFP_KERNEL);
+	if (!dp)
+		return -ENOMEM;
+
 	dp->dev = dev;
 
 	match = of_match_node(cdn_dp_dt_ids, pdev->dev.of_node);
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.h b/drivers/gpu/drm/rockchip/cdn-dp-core.h
index e9c30b9fd543..c10e423bbf06 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.h
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.h
@@ -38,6 +38,8 @@ enum vic_pxl_encoding_format {
 	Y_ONLY = 0x10,
 };
 
+struct cdn_dp_device;
+
 struct video_info {
 	bool h_sync_polarity;
 	bool v_sync_polarity;
@@ -63,16 +65,28 @@ struct cdn_dp_port {
 	u8 id;
 };
 
+struct cdn_dp_bridge {
+	struct cdn_dp_device *parent;
+	struct drm_bridge bridge;
+	struct rockchip_encoder encoder;
+	bool connected;
+	bool enabled;
+	int id;
+};
+
 struct cdn_dp_device {
 	struct device *dev;
 	struct drm_device *drm_dev;
-	struct drm_bridge bridge;
-	struct rockchip_encoder encoder;
+	int bridge_count;
+	struct cdn_dp_bridge *bridge_list[MAX_PHY];
+	struct drm_bridge *next_bridge_list[MAX_PHY];
+	const struct drm_edid *edid_cache[MAX_PHY];
 	struct drm_display_mode mode;
 	struct platform_device *audio_pdev;
 	struct work_struct event_work;
 
 	struct mutex lock;
+	bool next_bridge_valid;
 	bool connected;
 	bool active;
 	bool suspended;
-- 
2.53.0

Re: [PATCH 3/5] phy: rockchip: phy-rockchip-typec: Add DRM AUX bridge

[Heiko Stuebner]

Hi,

Am Donnerstag, 21. Mai 2026, 05:28:52 Mitteleuropäische Sommerzeit schrieb Chaoyi Chen:
> From: Chaoyi Chen <chaoyi.chen@rock-chips.com>
> 
> Using the DRM_AUX_BRIDGE helper to create the transparent DRM bridge
> device.
> 
> Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>

Reviewed-by: Heiko Stuebner <heiko@sntech.de>


@Vinod:
could you give this patch an Ack to go through the DRM tree please?

It is independent of any other phy changes, but needs the drm-patches 1+2
from this series, so ideally would go through the drm tree together with
them.

Thanks a lot
Heiko


> ---
>  drivers/phy/rockchip/Kconfig              |  2 ++
>  drivers/phy/rockchip/phy-rockchip-typec.c | 13 +++++++++++--
>  2 files changed, 13 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig
> index 14698571b607..9173d3b4fef4 100644
> --- a/drivers/phy/rockchip/Kconfig
> +++ b/drivers/phy/rockchip/Kconfig
> @@ -119,6 +119,8 @@ config PHY_ROCKCHIP_SNPS_PCIE3
>  config PHY_ROCKCHIP_TYPEC
>  	tristate "Rockchip TYPEC PHY Driver"
>  	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
> +	depends on DRM || DRM=n
> +	select DRM_AUX_BRIDGE if DRM_BRIDGE
>  	select EXTCON
>  	select GENERIC_PHY
>  	select RESET_CONTROLLER
> diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c
> index d9701b6106d5..48070b50416e 100644
> --- a/drivers/phy/rockchip/phy-rockchip-typec.c
> +++ b/drivers/phy/rockchip/phy-rockchip-typec.c
> @@ -54,6 +54,7 @@
>  
>  #include <linux/mfd/syscon.h>
>  #include <linux/phy/phy.h>
> +#include <drm/bridge/aux-bridge.h>
>  
>  #define CMN_SSM_BANDGAP			(0x21 << 2)
>  #define CMN_SSM_BIAS			(0x22 << 2)
> @@ -1162,16 +1163,24 @@ static int rockchip_typec_phy_probe(struct platform_device *pdev)
>  
>  	for_each_available_child_of_node(np, child_np) {
>  		struct phy *phy;
> +		ret = 0;
>  
> -		if (of_node_name_eq(child_np, "dp-port"))
> +		if (of_node_name_eq(child_np, "dp-port")) {
>  			phy = devm_phy_create(dev, child_np,
>  					      &rockchip_dp_phy_ops);
> -		else if (of_node_name_eq(child_np, "usb3-port"))
> +			ret = drm_aux_bridge_register_from_node(dev, child_np);
> +		} else if (of_node_name_eq(child_np, "usb3-port"))
>  			phy = devm_phy_create(dev, child_np,
>  					      &rockchip_usb3_phy_ops);
>  		else
>  			continue;
>  
> +		if (ret) {
> +			pm_runtime_disable(dev);
> +			of_node_put(child_np);
> +			return ret;
> +		}
> +
>  		if (IS_ERR(phy)) {
>  			dev_err(dev, "failed to create phy: %pOFn\n",
>  				child_np);
> 

Claude review: drm/bridge: Implement generic USB Type-C DP HPD bridge

[Claude Code Review Bot]

Overall Series Review

Subject: drm/bridge: Implement generic USB Type-C DP HPD bridge
Author: Chaoyi Chen <kernel@airkyi.com>
Patches: 7
Reviewed: 2026-05-25T21:00:52.011314

---

This series implements a generic USB Type-C DP HPD bridge infrastructure and refactors the Rockchip CDN-DP controller to support multiple bridge/PHY port selection without depending on extcon. The design goal is sound: decouple DP hotplug detection from specific USB-C controller drivers, and allow the CDN-DP controller to work with either of the two combo PHYs on RK3399.

The series has already collected Reviewed-by tags from Heikki Krogerus, Neil Armstrong, Luca Ceresoli, and Heiko Stuebner. The architecture is reasonable, but there are several correctness issues, most notably an **uninitialized variable bug** in patch 5 that could cause a kernel crash, and some logic concerns around the multi-bridge HPD/EDID switching path.

**Key concerns:**
1. Patch 5: `prev_port` used uninitialized — potential NULL-pointer dereference or use of garbage pointer
2. Patch 5: `cdn_dp_switch_port` sets `dp->active = true` but is called from EDID read context, which could leave stale state
3. Patch 5: `cdn_dp_connected_port` changes semantics — the old non-`next_bridge_valid` path now falls through to the `next_bridge_valid` block
4. Patch 1: No error handling for `drm_dp_hpd_bridge_register` failure in bus notifier
5. Patch 4: Condition change in `cdn_dp_probe` may inadvertently filter out valid port configurations

---

---
Generated by Claude Code Patch Reviewer

Claude review: drm/bridge: Implement generic USB Type-C DP HPD bridge

[Claude Code Review Bot]

Patch Review

This patch adds a new module that monitors the Type-C bus for altmode devices with DP SVID and automatically creates an HPD bridge for them.

**Issue 1: No error handling for bridge registration failure**
```c
if (is_typec_port_altmode(&alt->dev) && alt->svid == USB_TYPEC_DP_SID)
    drm_dp_hpd_bridge_register(alt->dev.parent->parent,
                               to_of_node(alt->dev.parent->fwnode));
```
`drm_dp_hpd_bridge_register()` returns a `struct device *` which can be an ERR_PTR. The return value is silently ignored. While there may not be much that can be done from a bus notifier, at least a `dev_warn()` would help debugging.

**Issue 2: Fragile device hierarchy assumption**
The comment documents the parent traversal (`alt->dev.parent->parent` = USB-C controller device), but this is a fragile assumption about the device hierarchy. If the hierarchy ever changes, this will silently break. Consider whether there's a more robust API to get the controller device.

**Issue 3: Module exit doesn't clean up bridges**
`drm_aux_hpd_typec_dp_bridge_module_exit()` only unregisters the notifier but doesn't clean up any bridges that were registered via `drm_dp_hpd_bridge_register()`. Those are `devm`-managed on the controller device, so they'll survive module unload. This may be intentional, but it means loading/unloading this module repeatedly could have unexpected interactions.

**Minor: Missing MODULE_AUTHOR**

---
Generated by Claude Code Patch Reviewer

Claude review: drm/bridge: aux: Add drm_aux_bridge_register_from_node()

[Claude Code Review Bot]

Patch Review

Clean patch. The refactoring to make `drm_aux_bridge_register()` a wrapper around the new `_from_node()` variant is the right approach.

**Minor nit:** The kdoc on the original `drm_aux_bridge_register()` is updated to add `@np` but that parameter doesn't exist on the old function — the `@np` doc belongs only on the new `drm_aux_bridge_register_from_node()`. Looking more carefully:

```c
/**
 * drm_aux_bridge_register - Create a simple bridge device to link the chain
 * @parent: device instance providing this bridge
 * @np: device node pointer corresponding to this bridge instance
```

This kdoc block is placed on `drm_aux_bridge_register_from_node()` after the rename, so the function name in the doc comment (`drm_aux_bridge_register`) is now wrong — it should say `drm_aux_bridge_register_from_node`. The `@np` parameter description should also mention that NULL falls back to the parent device's of_node.

---
Generated by Claude Code Patch Reviewer

Claude review: phy: rockchip: phy-rockchip-typec: Add DRM AUX bridge

[Claude Code Review Bot]

Patch Review

Straightforward integration of the aux bridge into the Rockchip Type-C PHY driver.

**Issue: Error check ordering**
```c
if (of_node_name_eq(child_np, "dp-port")) {
    phy = devm_phy_create(dev, child_np, &rockchip_dp_phy_ops);
    ret = drm_aux_bridge_register_from_node(dev, child_np);
} else if ...

if (ret) {
    pm_runtime_disable(dev);
    of_node_put(child_np);
    return ret;
}

if (IS_ERR(phy)) {
```

If `devm_phy_create()` succeeds but `drm_aux_bridge_register_from_node()` returns `-EPROBE_DEFER`, we return the error but the PHY remains registered (via devm). This is fine because devm will clean it up, but it means the order of checking `ret` before `IS_ERR(phy)` could mask a PHY creation failure. If `devm_phy_create` fails AND `drm_aux_bridge_register_from_node` fails, the bridge error is returned while the PHY error is lost. Consider checking `IS_ERR(phy)` first.

**Kconfig dependency:**
```
depends on DRM || DRM=n
select DRM_AUX_BRIDGE if DRM_BRIDGE
```
This is a reasonable conditional select pattern for optional DRM dependencies.

---
Generated by Claude Code Patch Reviewer

Claude review: drm/rockchip: cdn-dp: Support handle lane info without extcon

[Claude Code Review Bot]

Patch Review

Makes the extcon device optional in CDN-DP, falling back to `phy_get_bus_width()` for lane count.

**Issue: Potentially incorrect filter condition in probe**
```c
-       if (IS_ERR(extcon) || IS_ERR(phy))
+       if (IS_ERR(phy) || PTR_ERR(extcon) != -ENODEV)
            continue;
```
The original skips the port if either extcon OR phy is an error. The new code skips if phy is an error OR if `PTR_ERR(extcon) != -ENODEV`. But if `extcon` is **valid** (not an error), then `PTR_ERR(extcon)` is undefined behavior — it would cast a valid pointer to a long and compare it against `-ENODEV`. This condition should be:
```c
if (IS_ERR(phy) || (IS_ERR(extcon) && PTR_ERR(extcon) != -ENODEV))
    continue;
```
The intent is: skip if phy fails, or if extcon failed with something other than `-ENODEV` (meaning extcon is genuinely absent vs. a real error like `-EPROBE_DEFER`). The current code is **buggy for the case where extcon is valid**.

Wait — re-reading: extcon is fetched above with `extcon_find_edev_by_node`. If it returns a valid pointer, `PTR_ERR()` of a valid pointer is not `-ENODEV`, so the `continue` would fire, skipping valid ports. This is a real bug.

**Issue: `property.intval = 0` default for polarity**
```c
property.intval = 0;
if (port->extcon) {
    ret = extcon_get_property(port->extcon, EXTCON_DISP_DP,
                  EXTCON_PROP_USB_TYPEC_POLARITY, &property);
```
When extcon is absent, polarity defaults to 0, which assumes normal polarity. This seems reasonable but should be documented or verified against the hardware behavior when the Type-C controller is managing polarity via the PHY directly.

---
Generated by Claude Code Patch Reviewer

Claude review: drm/rockchip: cdn-dp: Add multiple bridges to support PHY port selection

[Claude Code Review Bot]

Patch Review

This is the largest and most complex patch in the series.

**Bug: `prev_port` used uninitialized**
In `cdn_dp_bridge_edid_read()`:
```c
struct cdn_dp_port *prev_port;
...
if (dp->bridge_count > 1 && !port->phy_enabled) {
    for (i = 0; i < dp->bridge_count; i++) {
        if (dp->bridge_list[i] != dp_bridge && dp->bridge_list[i]->enabled)
            goto get_cache;
        if (dp->port[i]->phy_enabled)
            prev_port = dp->port[i];
    }

    /* Switch to current port */
    if (prev_port) {
        ret = cdn_dp_switch_port(dp, prev_port, port);
```
`prev_port` is never initialized to `NULL`. If no port has `phy_enabled` set, `prev_port` contains stack garbage, and the `if (prev_port)` check passes with a random non-zero value, leading to a crash in `cdn_dp_switch_port()`. **Fix: initialize `prev_port = NULL`.**

**Issue: `cdn_dp_switch_port` sets `dp->active = true` from EDID context**
```c
static int cdn_dp_switch_port(struct cdn_dp_device *dp, ...)
{
    if (dp->active)
        return 0;
    ...
    dp->active = true;
    dp->lanes = port->lanes;
```
This function is called from `cdn_dp_bridge_edid_read()`, which is a detect/probe path. Setting `dp->active = true` during EDID read means the subsequent `cdn_dp_enable()` call from `cdn_dp_bridge_atomic_enable()` will return early (`if (dp->active) return 0`), potentially skipping important initialization that normally happens during `cdn_dp_enable()` (firmware init, clock enable). This seems like it could leave the driver in an inconsistent state.

**Issue: `cdn_dp_connected_port` logic change breaks non-bridge path**
```c
for (i = 0; i < dp->ports; i++) {
    port = dp->port[i];
    lanes[i] = cdn_dp_get_port_lanes(port);
    if (!dp->next_bridge_valid)
        return port;
}
```
In the old code, the function returned the first port with non-zero lanes. Now with `!dp->next_bridge_valid`, it returns the first port **unconditionally** (even if `lanes[i]` is 0). This is a regression for the extcon path — a port with zero lanes would now be returned as "connected". Should be:
```c
    if (!dp->next_bridge_valid && lanes[i])
        return port;
```

**Issue: `bridge_count` vs `ports` inconsistency**
The `next_bridge_valid` path in `cdn_dp_connected_port()` iterates with `dp->bridge_count`:
```c
for (i = 0; i < dp->bridge_count; i++) {
    if (lanes[i])
        return dp->port[i];
}
```
But `lanes[]` was populated over `dp->ports` iterations. If `bridge_count != ports`, some `lanes[]` entries could be uninitialized or we could access `dp->port[i]` out of bounds.

**Issue: `cdn_dp_bridge_detect` not updated for multi-bridge**
The `cdn_dp_bridge_detect()` function still only checks `dp->connected`, but the per-bridge `dp_bridge->connected` flag is only checked in `cdn_dp_bridge_mode_valid()`. The detect callback should probably also consider the per-bridge connected state, otherwise all bridges report the same connection status.

**Design: EDID caching**
The EDID caching design (`edid_cache[MAX_PHY]`) is reasonable for the port-switching scenario. The `drm_edid_dup()`/`drm_edid_free()` calls appear correctly paired.

**Good: `devm_drm_bridge_alloc` usage**
Moving from a single bridge embedded in `cdn_dp_device` to dynamically allocated `cdn_dp_bridge` structs is the right structural change.

**Cleanup needed in unbind:**
```c
for (i = 0; i < dp->bridge_count; i++) {
    encoder = &dp->bridge_list[i]->encoder.encoder;
    encoder->funcs->destroy(encoder);
    drm_bridge_put(dp->next_bridge_list[i]);
}
```
`drm_bridge_put(dp->next_bridge_list[i])` could be called with NULL if `next_bridge_list[i]` wasn't populated (e.g., extcon path where `bridge_count = 1` but `next_bridge_valid = false`). Should check for NULL before calling `drm_bridge_put()`.

---

**Summary:** The series has the right architectural direction but patch 5 has several correctness issues that need fixing before merge, most critically the uninitialized `prev_port` and the `cdn_dp_connected_port` logic regression. Patch 4 also has a real bug in the probe filter condition.

---
Generated by Claude Code Patch Reviewer